BEL Electronics Question Paper

1. Numerical problem based on modulation index fc, fm………. (formula based direct queston).
2. Poles & zeroes are at .01,1,20,100…… find phase margin/angle at f=50Hz. ans -90(By drawing bode plot)
3. In n-type enhancement mode MOSFET drain current———– options are- increase/decrease with
inc/dec in drain/gate voltage.
ans(d)
4. Gain of an directional antenna 6db P=1mw find transmitted power………(use Ptr= G * P.)
5. Multiplication of two nos 10101010 & 10010011 in 2’s complement form..
6. A ckt is given suppplied with 15v with a series of resistance of 1k and a parallel combination of 12V zener diode and 2k resistance. FInd current through 2k resistance.
Ans: 6mA
7.A MP has 16 line data bus & 12 line addr bus find memory range……….Ans..4K(4*1024bytes)
8.Divide by 12 counter require minimum ….. no of flip flops Ans. 4
9.Storage time in p-n junction.
10.Succesive approx. use in …. Ans ADC(analog to digital)
11.Pre-emphasis require in ……… low freq/high freq signal.
12.Handshake in MP ……….. Ans to communicate with slower peripherals.
13. Binary equivalent of 0.0625 Ans. 0.0001
14.Which code is self complement of itself
15.Excess three code of an given binary no.
16.When we add 6 in BCD operations……. Ans. if result exceed valid BCD nos.
17.Shottky diode has better switching capability because it switch between…….
18.Figure of Merit is same as……
19.Swithcing in diode happens when….
20.During forward bias majority charge conc. in depletion layers inc/decrease…..
21.Channel capacity depend on……. Ans. Usable frequency or bandwidth
22.A 2kHz signal is passed through an Low pass filter having cut-off freq 800Hz o/p will be
23. Carrier amplitude 1v, peak to peak message signal 3mv find modulation index.
24.A 12V signal is quantized into two V/14 & 6 equal V/7 determine quantization error.

Part II True & false…...( 1 mark each) with 50% -ve marking
1.Power dissipation in ECL is minimum………. False
2.Fourier Transform of a symmetric conjugate function is always real …. True
3.Divide by 12 counter requires a minimum of 4 flip flops…….True
4.Boron can be use as impurity to analyse base of a npn transistor…….True

BHEL 2008 Electrical Question Paper

1. The ratio of two specific heats of air is equal to. = 1.41

2. An engine operates between temperature of 9000K and T2 and another engine between T2 and 8000K. For both to do equal work, value of T2 will be. = 6500K

3. A perfect gas at 270C is heated at constant pressure till its volume is double. The final temperature is = 3270C

4. Internal energy of a substance depends on = Temperature

5. Work done in compressing 1kg of gas adiabatically from p1,V1,T1 to p2, V2, T2 is equal to = Cv(T2-T1)

6. Indicated power of a 4-stroke engine is equal to = pLAN/2

7. The unit of entropy is = J/kg 0K

8. Which of the following is not an internal combustion engine : a) 2 stroke petrol engine b)4 stroke petrol engine c) Diesel engine d) steam engine e) Gas turbine. = (d)

9. Air fuel ratio in a jet engine is = 60:1

10. If one cylinder of a diesel engine receives more fuel than the others, then for that cylinder the: a) exhaust will be smoky b) piston rings would stick into piston grooves c) exhaust temperature will be high d) engine starts overheating e) all of the above. = (e)

11. A distributor in spark ignition engines performs the function of : = Providing the correct firing order in engine

12. The spark plug gap is normally maintained at: = 0.45 to 0.6mm

13. Which of the following does not relate to C.I. engine:: a) fuel pump b) fuel injector c) governor d) carburetor e) flywheel = (d)

14. What is the value of Prandtl No.?

15. In domestic refrigerator, the tubes at the back of the refrigerator are: a) evaporator b) condenser c) capillary tubes d)………

16. Wet bulb temperature is. = indication of amount of moisture in air

17. Which refrigerants has the highest critical point temperature. = Freon-11

18. On psychrometric chart, dry bulb temperature lines are. = Vertical

19. The line of action of the buoyant force acts through the. =centroid of the displaced volume of fluid

20. Surface tension has the units. = newtons/m

21. A pressure of 25m of head of water is equal to. =245kN/m2


22. For a submerged body to be in stable equilibrium, the centre of gravity should be. =Below the centre of buoyancy.

23. Runaway speed of a hydraulic turbine is: = the speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open.


24. The actual velocity at vena contracta for flow through an orifice from a reservoir of height H=?. =Cvv2gH


25. 100KW is to be transmitted by each of two separate shafts. A is turning at 250rpm and B at 300rpm. Which shaft must have greater diameter.: = B


26. In a free vortex motion: = each particle moves in a circular path with a speed varying inversely as the distance from the centre.


27. A centrifugal pump has speed-1000rpm, Flow-1200l.p.m, Head-20m, Power-5H.P. If its speed is increased to 1500rpm, new flow will be.: = 1800l.p.m


28. 10m of water column is equal to = 100kN/m2


29. M.I. of a circular area about an axis perpendicular to the area is: = pr4/2


30. A projectile is fired at an angle ? to the vertical. Its horizontal range will be maximum when ? is . =450


31. An elevator weighing 1000kg attains an upward velocity of 4m/sec in two seconds with uniform acceleration. The tension in the supporting cables will be = 1200kg.


32. A 13m ladder is placed against a smooth vertical wall with its lower end 5m from the wall. What should be the co-efficient of friction between ladder and floor so that it remains in equilibrium. = 0.21

33. Sintered and tungsten carbides can be machined by: = EDM


34. A car is moving with a velocity of 60km/hr and possesses energy of 5x105 joules. The mass of the car will be. =3000kg.


35. A beam of length l, having uniform load w kg/unit length is supported freely at the ends. The moments at mid span will be: = wl2/8. http://www.ChetanaS.org

36. A boiler shell 200cm dia and plate thickness 1.5cm is subjected to internal pressure of 1.5MN/m2, then the hoop stress will be. = 100N/m2

37. A body weighing 2kg in air weights 2.5kg when submerged in water. Its specific gravity is. = 6


38. Two identical leaf springs of spring constant k are arranged like cantilevers in parallel and attached at free end by a spring of spring constant k. The equivalent spring constant of combination is; = 1.5k.

39. Automobile steering gear is an example of: = lower pair.

40. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central diop is y, the horizontal pull at each support is: = wl/y OR


41. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is. = Universal coupling.

42. Two cars travel in the same direction at 40km/hr at a regular distance. A car comes in the opposite direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two cars?

43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.


44. Brittle coating technique is used for: = experimental stress analysis.


45. Factor of safety is the ratio of: = yield stress/working stress.


46. Type of gear used for non-intersection perpendicular shafts: = Hypoid gears.


47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel


48. The product of Cupola is called: = cast iron


49. Brinell tester uses a hardness steel ball of size: = 10mm


50. To transmit power from one rotation shaft to another whose axes are neither parallel nor intersecting, use: = Spiral gear.


51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond grit.


52. In break-even analysis, total cost consists of: = Fixed cost + Variable cost.

53. PERT is: = event oriented technique


54. The amount deducted from the salary of workers towards employees provident fund is : =deposited in the account of worker with Provident Fund Commissioner.


55. Bar charts are suitable for: = minor works.

56. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one revolution of arm. = 5 rev.


57. ----- on a PERT/CPM chart represents: = a significant event representing some mile-stone


58. Electron volt is the unit of : = Energy.

59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.

60. Seamless tubes are made by?


61. Why DC current is not used in transformer?


62. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure energy.


63. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance force of the sand?

BEL Bangalore 2011 Placement Paper

1. Which one of the following is called the ‘metal of future’?

(A) Copper
(B) Iron
(C) Titanium
(D) Aluminum

2. The earliest coins of India were made of ?

(A) Copper
(B) Gold
(C) Lead
(D) Silver

3. The Mongols appeared for the first time on the banks of Indus during the reign of?

(A) Balban
(B) Iltutrnish
(C) Qutubuddin Aibak
(D) Razia

4. The first woman ruler of medieval India was?

(A) Chand Bibi
(B) Durgavati
(C) Noorjahan
(D) Razia

5. The Moplah Rebellion (1921) took place in?

(A) Malabar
(B) Marathawada
(C) Telengana
(D) Vidarbha

6. Which part of the Constitutions of India has been described as the: Soul of the Constitution ?

(A) Directive principles of State policy
(B) Fundamental rights
(C) Preamble
(D) Right to constitutional remedies

7. The first state to implement the Panchayati Raj System in India was?

(A) Uttar Pradesh
(B) Rajasthan
(C) Gujarat
(D) Karnataka

8. Who has the right to seek advisory opinion of the Supreme Court on any question of law?

(A) Prime Minister
(B) President
(C) Any High Court
(D) All of the above

9. Consider the following statements about the Governor of a State

1. He is appointed by the President.
2. He holds office at the pleasure of the President.
3. The executive power of the: State vests in him.
4. Normally he holds office for five years.
Select the correct answer from the codes given below
(A) l and 2
(B) 1,2 and 3
(C) 1,2 and 4
(D) All the four

10. Which one of the following pairs is not correctly matched ?

(A) Ahmedabad—Sabarmati
(B) Lucknow —Gomti
(C) Bhubaneshwar—Mahanadi
(D) Ujjain-Shipra

11. Dilwara Jain temple is situated at?

(A) Palitana
(B) Mount Abu
(C) Sonagiri
(D) Girinarji

12. Which one of the following is the biggest shipping canal in the world?

(A) Kiel Canal
(B) Panama Canal
(C) Soo Canal
(D) Suez Canal

13. Where was the battle of Plassey fought?

(A) Karnal
(B) Haldighati
(C) Mysore
(D) Bengal

14. Who was the first Vice-President of India?

(A) Dr. S. Radhakrishnan
(B) Dr. Rajendra Prasad
(C) C. V. Raman
(D) Jawahar Lal Nehru

15. What was the reason behind the mutiny of 1857?

(A) Cartridge containing fat
(B) Frustration in soldiers
(C) Failure of British Government
(D) Administrative research

16. For VHF interfering waves generated by automobile ignition systems or other electrical equipment located close to the ground, specify which of the following components of the interfering signal are significant at receiving locations such as used in the reception of TV signals:
        
1.Horizontal polarization component
2.Vertical polarization component
3. Both horizontal and vertical polarization components
4. Neither horizontal nor vertical polarization components
 
17. The ratio of lower frequency limit to the MUF for radio communication at short-wave is generally
        
1. Smaller at night than in the day time
2. Larger at night than in the day time
3. Same at night and in the day time
4. A maximum during the evening times
 
18. Two UHF amateur radio antenna placed at the same height and 30 statute miles apart are to be such that each is on the radio horizon line of the other. The height of the antennas should be
       
a.  56.25 ft            b. 112.5ft         c. 150ft            d. 225ft
 
19. A transmitter with a radiated power of 1 KW produces a field strengthof 300 mv/m at a distance of 1 Km from the antenna. If the transmitter power is increased to 50 KW and the vertical directivity of the antenna is increased by a factor of 1.41, the field strength a the same distance from the antenna is approximately

a.  1.5 V/m            b. 2.115 V/m                c. 3.0 V/m      d. 6.0 V/m
 
20. The directive gains of non-resonant and resonant wire antennas of equal length are approximately in the ratio of
        
a.. 4:1       b. 1.5:1            c. 1:1                d 3:1

21.A simple wire radiator produces a radiation field of intensity 100 mV/m at a distance point 25 Km away. The field produced (in mV/m) at a point 50 Km away in the same direction is
       
a. 25        b.50                 c. 12.5             d. 100
 
22. Assuming the plane of polarization of the incoming wave and the plane of the receiving antenna to be the same, the effective height of the receiving antenna is proportional to
        
1. Radiation resistance
2. Power gain of the antenna
3. Physical area of the antenna
4. Wavelength, assuming other parameters being same
 
23. The function performed by the following circuits is

1. General combinational logic
2. Exclusive OR logic
3. Exclusive NOR logic
4. Digital comparator logic
 
24.  Narrow trigger pulses are required to be generated from a square wave pluse train (pulse width = T). The linear wave shaping circuit would be an RC circuit (time constant = T) with the following features:

1. High pass with T << T
2. High pass with T >> T
3. Low pass with T >> T
4. Low pass with T << T
 
25. The circuit given below acts as

1. An OR gate
2. An AND gate
3. An inverter
4. A NOR gate
 
26. In the circuit shown below. if  R = 0 and S = 1, the outputs Q and Q'  will be

1. Q low, Q'  high
2. Both low
3. Q high, Q'  low
4. Both high

27. Schmitt trigger buffers are normally used as input buffers to digital logic circuit to achieve
       
1. Higher isolation
2. Higher fan-in-capability
3. Higher drive capability
4. Higher noise-immunity

28. For a reverse-biased PN junction. If the applied voltage is doubled the junction capacitance decreases by a factor of 2 ½. Assuming the junction acts as a parallel plate condenser, the average spacing between the plates changes by a factor of
        
1. 22         b.2            c. 1/21/2            d. 21/2
 
29. Many frequency sources use a piezo-electric resonator in the feedback circuit essentially to achieve a
        
1. Miniature product
2. Low cost design
3. Stable frequency
4. Large output power

30. A pulse train has the following characteristics:

Peak amplitude = 10 V, Pulse ON time 1 sec

Pulse OFF time = 4 sec

The pulse train is passed through a high pass RC filter with a large time constant.      The amplitude of the positive peak at the output will be

1. .10 V                b. 2V        c. 4V             d. 8V

BEL 2011 Placement Paper

1. In which of the following movements ‘Vande Mataram’ was adotped for the first time as a slogan for agitation?

(A) Revolt of 1857
(B) Partition of Bengal in 1905
(C) Non-cooperation Movement in 1922
(D) Quit India Movement in 1942

2. Who warned Gandhiji not to encourage fanaticism of Muslim religious leaders and their followers?

(A) Agha Khan
(B) AjmaI Khan
(C) Hasan Imam
(D) Mohammad Ali Jinnah

3. Which one of the following is not correct about the Congress Session.of Lucknow, 1916?

(A) Ambika Charan Majumdar was not the president of this session
(B) In this session the reunion between the liberal and the extremist was established
(C) Mahatma was apprised the problems of the peasants Champaran for the first time
(D) None of the above

4. Kanpur conspiracy case was against the leaders of?

(A) Khilafat Movement
(B) Non-cooperation Movement
(C) Communist Movement
(D) Revolutionary Movement

5. In India “Currency Notes issue system” is based on?

(A) Minimum reserve system
(B) Proportional reserve system
(C) Fixed exchange rate system
(D) Full convertibility system

6. ‘Disguised’ unemployment means?

(A) Persons with no jobs
(B) Unemployment among house wives
(C) Unemployment among per sons above 60 years pf age
(D) Employment of more persons in a job which lesser number of persons can perform

7. Which of the following statements are true about the income tax in India?

1. It is a progressive tax,
2. It is a direct tax.
3. It is collected by the Government.
4. It is a proportional tax Select the correct answer from the code given below

Codes:
(A) 1 only
(B) 1 and 2 only
(C) 1,2and3only
(D) 2, 3 and 4 only

8. ‘SIDBI’ has been established to-

(A) Finance small scale industries
(B) Finance cottage industries
(C) Finance large scale industries
(D) Finance public sector under takings

9. Gangubai Hangal, who died a few months ago, was a?

(A) Classical singer
(B) Dancer
(C) Painter
(D) Sitar player

10. Deep Joshi has recently been given Raman Magsaysay Award in the category of?

(A) Government service
(B) Public service
(C) Community leadership
(D) Emergent leadership

11. The missing number in the following series: 5,10,13,26,29, 58, 61,…Is?

(A) 122
(C) 128
(B) 125
(D) 131

12. If 2 jeans and 3 shirts cost Rs. 4,000 and jeans and 2 shirts cost Rs. 3,500, how much does a jeans cost?

(A) Rs. 1,500
(B) Rs 1,000
(C) Rs. 500
(D) Rs. 2,000

13. Which one of the following expresses error in computer data?

(A) chip
(B) byte
(C) bug
(D) bit

14.Assertion (A) Graphite is a good lubricant. Reason (R) Graphite is good conductor of electricity. Select the correct answer from the codes given below Codes:

(A) Both (A) and (R) are true and (A) is the correct explanation of (A)
(B) Both (A) and (A) are true but (H) is not the correct explanation of (A)
(C) (A) is true but (R) is false
(D) (A) is false but (A) is true

15. Acid rain is caused by pollution ot environment by?

(A) Carbon dioxide and Nitrogen
(B) Carbon monoxide and Carbon dioxide
(C) Ozone and Carbon dioxide
(D) Nitrous oxide and Sulphur dioxide


16. The professional printed circuit board generally use the following as the raw material:
       
1.Paper base bakelite copper clad sheet
2. Glass epoxy copper clad sheet
3.Tin plated Nylon sheet
4. Silver plated pyrex sheet
 
17. Many switch contacts use silver as the material because
        
1. It is a good electrical conductor with low contact resistance
2. Silver does not tarnish
3. It is easily shaped as per requirement
4. It is very hard and does not wear off
  

18. A resistance of approximate value 85W is to be measured by using an ammeter of range 0-1 A having a resistance of 20 W and voltmeter of range 0-50V having a resistance of 5000W. Two arrangement for the measurement are shown in the figure below. Which method would you recommend?
        
1. Method X
2. Method Y
3. Either X or Y
4. Neither X nor Y
  

19. The value of capacitance across points A & B in the circuit shown below is (in microfarads)

a. .3         b. 1         c. 0.67          d. 0.33
  
20. It is proposed to fabricate a simple Ohm meter for measuring  resistor values. A milliammeter with an internal resistance of 50 W is available. Choosing a configuration using a 3 V battery, a large resistance and the ammeter in a loop, the unknown resistor is proposed to be measured by noting the current initially and then connecting the unknown resistor across the ammeter. If the ratio of the two current is 2, what is the value of the unknown resistor (rn W ) ?
        
a. 3000         b. 150         c. 100         d. 50
  
21.The current I flowing into the branch indicated by an arrow  in the circuit shown is equal to

        
a. 2 Amp         b. 0.5 Amp        c. 1 Amp         d. 0.25 Amp
 
22. For the circuit shown, the maximum power is delivered to the load resistance RL when the value of Rg is

a. 2 ohms        b. zero         c. 10 ohms          d. infinity
  
23. A signal generator is available in the laboratory, which is in good condition except for the attenuator dial which has got displaced. In order to calibrate this, a high frequency oscilloscope is available. At a particular setting of the knob an open circuit voltage of 450 mV rms is measured. If the impedance of the generator is 50 ohms, the setting of the attenuator dial is to be adjusted for
        
a. 6 dBm      b. 1 dBm          c. 0 dBm           d. 10 dBm
  
24. The relation Loge (X + Loge (1 + X) = 0 also means that
       
1. X2 + X + 1 = 0
       
2. X2 + X - 1 = 0
        
3. X2 + X + e = 0
        
4. X2 + X – e = 0
  
25. The Laplace transform of the function f(t) = cos wt is
        
1. w/(s2 + w2)
        
2. s2/(s2 - w2)
        
3. w2/(s2 + w2)

4. s/(s2 + w2)
 
26. If a = b = c, one value of X which satisfies the equation

=0 is given by

a.   x=a         b. x=b         c. x=c         d. x=0
 
27. An LC oscillator is being analysed. If the LC tank circuit (with quality factor = Q) is isolated from the amplifying device, the impedance at the resonant frequency as measured looking into the amplifier will be
        
1. Q r [LC]1/2

2. ½ rp r [LC]1/2
       
 3.  – Q r[LC]1/2
        
4.  Q r [LC]1/2
 

28. A battery eliminator is required to be constructed and an assortment of rectifiers, resistors and capacitors is available. However, the step down transformer available has no center tap. The following configurations for the rectifier are feasible. The one giving the lowest ripple will be
        
1. Full wave rectifier
2. Half wave rectified
3. Bridge rectifier
4. None
 
29. Chokes used in rectifier filter circuits are wound on a core with a small air gap. This is done in order to
        
1. Get as high an inductance as possible
2. Prevent saturation of the core
3. Absorb the ripple effectively
4. Prevent loading the transformer
 
30. An integrated circuit linear regulator is used at the output of a power supply having a ripple of 1 V rms. Assuming that the IC represents a typical design generally available, the output rms ripple to be expected will be
        
a.. 0.1 V rms      b. 0.1 mV      c. 100 mV       d. 1.0 V rms

Gujarat Narmada Valley Fertilizers Company Limited (GNFC) Recruitment

Gujarat Narmada Valley Fertilizers Company Limited (GNFC)
Narmadanagar, Dist: Bharuch - 392015, Gujarat

The applications are invited from the eligible candidates for following positions :

1. Chemical/ Shift Engineer (on contract)
2. Graduate Engineer Trainee (GET) (Chemical) 
3. Graduate Engineer Trainee (GET) (Instrument) 
4. Asst. Operator (on contract) 
5. Diploma Engineer Trainee (DET) (Chemical) 

How to Apply :  Interested candidates may fill-up the blank form online  as well as upload the detailed resume within 10 days starting from 19/10/2011. 

Please visit https://www.gnfc.in/career.html for details and application form.
 

Balmer Lawrie & Co. Ltd. Junior Supervisor Recruitment

Balmer Lawrie & Co. Ltd.
Regional Human Resource Department-Western Region

Balmer Lawrie & Co. Ltd. invites application for the following posts

1. Junior Supervisor (Electrical / Electronics)
• Pay Scale : Rs. 9000-22000
• Age : 30-35 years (Relaxable as per rules)
• Qualification :Degree / Diploma Holder in Electrical Engineering

Last Date for receipt of online application : 31.10.2011

    The application form, in prescribed format and duly completed in all respect, should be sent either through Registered Post / Courier / Speed Post to the address mentioned below: The Assistant General Manager (HR)-WR, Balmer Lawrie & Co. Ltd. , 5- J. N. Heredia Marg, Ballard Estate, Mumbai- 400 001

For Experience , More Detail , Please visit http://www.balmerlawrie.com/employment.asp

Website : http://www.balmerlawrie.com

212 Engineer Posts @ BHEL

BHEL the country's premier Engineering organization and one of the NAVRATNA PSUs, catering to the core sectors of Indian economy, viz. Power Generation, Transmission, Industry, Transportation, Telecommunication and Renewable Energy, requires Experienced engineers in echanical/Electrical/Civil/Electronics/Instrumentation/Chemical Disciplines, for Project Sites (Domestic & Overseas) of Power Sector Northern Region (FS-NR), Power Sector Eastern Region (PS-ER), Power Sector Western Region (PS-VVR), Power Sector Southern Region (PS-SR) and Project Engineering & Systems Division (PESD), Hyderabad. Details of the Power Sector Regions and PESD, Hyderabad, and the Projects under execution by them, are available in our vvebsite¬http:Ucareers.bheLin. The requirement is given below:

1. ERECTION: 98posts
2. TXS (commissioning)/SAS: 38posts
3. PIPlNG: 07posts
4. Civil: 11posts
5. MM: 23posts
6. Electrical & C&F: 23post
7. CHEMICAL: 01post
8. Project MG MT: 03posts
9. Tendering COMML: 02posts
10. Sub Contracting: 02posts
11. Quality & HSE: 04posts
12. 2(Two) Vacancies are identified for Hydro Turbine Function for PSER in the grade of E3.

Age limit: Lipper Age limit is relaxable by 3 years for OBC (Non Creamy Layer).
Qualifications: Full time. Bachelor's Degree in Engineering or Technology in Mechanical' Electrical 1 Civil I Electronics I Instrumentation 1 Chemical discipline with at least 60% marks (50% for SC/ST) in aggregate of all years I semesters or equivalent CGPA, from a recognized Indian University I Institute.

How to Apply: The submission of applications will be on-line only through our recruitment website ¬http://careers.bheLin

Important Dates:
Start of Online submission: 19.10.2011
Close of Online submission: 01.11.2011
Last Date for receipt of Hard Copies from far flung areas: 14.11.2011
Last Date: 07.11.2011

For more details Click here

Mangalore Refinery and Petrochemicals Ltd. Workman posts

Mangalore Refinery and Petrochemicals Limited (MRPL), a subsidiary of ONGC and a Mini Ratna Company, is focused on efficiency and growth. The company is recognized today as the leading refinery in India in terms of all round performance, having won many awards in Encon, Safety, Quality, Exports etc. The company is executing an Expansion & Up gradation Project, at an estimated cost of about $ 3.0 Billion and an Aromatics Project, on behalf of ONGC – Mangalore Petrochemicals Ltd., at an estimated cost of $ 1.2 Billion. Other initiatives include foray into retail marketing, direct marketing of ATF etc. In case you are the one looking for real challenges, here is the opportunity.

Trainee - Workman (Process): 100posts
Qualification: B.Sc (Chemistry)/ Diploma in Chemical Engineering.
Max. Age as : on 31/08/2011: 28years
Pay Scale: 10500-24500
HOW TO APPLY: Candidates should apply online only. After submission of online application, online receipt will be generated which has to be downloaded by the candidate The Candidates are required to send the acknowledgement slip with affixed photograph along with Xerox copy of educational/experience/caste certificates to, The Chief Manager(HR),Mangalore Refinery and Petrochemicals Limited, Post Kuthethur,Mangalore-575030

Imp dates: Last Date for filling On-Line Applications: 03/11/11, Time: 1800 hrs.
Last date for receipt of documents along with On-line acknowledgement slip: 10/11/11

For more details Click here

472 Engineers posts @ Haryana Staff Selection Commission

Applications are invited through Registered Post by Haryana SSC for the under mentioned posts on the prescribed application form. The candidates should specify on the top of the envelope the word - Advt. No., Name and Category of the post applied for.

Junior Engineer (Civil): 422
Qualification: Diploma in Civil Engineering (ii) Hindi/ Sanskrit up to Metric
Pay Scale: Rs.9300-34800 grade pay Rs. 3600,
Age: 17-40 years.

Junior Engineer (Mechanical): 50 (earlier 32 posts were published).
Qualification: Diploma in Mechanical Engineering (ii) Hindi/ Sanskrit up to Metric.
Pay Scale: Rs.9300-34800 grade pay Rs. 3600,
Age: 17-40 years,
Fee: Fee at the following rates should be deposited in the Haryana Govt. Treasury under the head "0051 - H.P.S.C.-(103)-Staff Selection Commission, Haryana- Application fee and other receipts"
1. General- Rs.150/- .
2. SC/BC/ ESM/ PH candidates of Haryana- Rs.35/- /
3. No concession of fee for SC/BC/ESM from other states.
Candidates from outside will be treated as General and should send fee by Postal Order which should be in the favour of "Secretary, Haryana Staff Selection Commission" payable Panchkula.

How to apply : Application forms complete in all respect - only one form should be filled by the candidate - in their own handwriting in capital letters and signed in the specified space should be sent only through Registered Post to the Secretary, Haryana Staff Selection Commission, Bay No 67-70, Sector-2, Panchkula-134151. All the column of the application form should be filled.

Last Date: 04/11/2011.

For more details Click here

420 Graduate Apprentices posts @ Bharat Electronics Limited

Bharat Electronics Limited, a leading Navratna Public Sector Enterprise, under the Ministry of Defense, propose to engage Engineers as Graduate Apprentices (420 posts) under the Apprenticeship Act 1961, purely for ONE year in the following designated subject fields for Bangalore Complex.

Graduate Apprentices: 420posts

• Civil Mechanical Computer Science(only)
• Electronics Telecommunication
• Electronics & Communication
• Electronics & Telecommunication

Qualification: 1st Class in Engineering and Pass class for SC/ST/PHP candidates.
Note: Candidates should have passed Engineering Degree examination on or after 01.01.2009.
Age limit: Candidates should be below 25 years as on 01.12.2011. Upper age limit is relaxed for 5 years in case of SC, ST, & PHP candidates only.
Mode of Selection: Selection will be through interview only.

How to apply: Walk -in Selection for Graduate in Engg for the Graduate Apprenticeship Training On 18 th & 19th November, AT CLD/BEL. Following are the documents to be produced in original for verification: SSLC Marks Card (as proof of age).Degree Original Certificate or Provisional Degree certificate (PDC). SC/ST/PHP certificates (if any for verification). Only Indian Nationals are eligible.

Walk-in-interview: 18th & 19th Nov. 2011 8:30 A.M.

For more details Click here

Inland Waterways Authority of India

Inland Waterways Authority of India
A Statutory Body under Ministry Of Shipping
Govt. of India, Head Office A-13, Sector-1,Noida, U.P., Pin-201301

Inland Waterways Authority of India, invites applications for the following posts to be filled up on direct recruitment basis

1. Supervisor : 06 Posts
• Pay Scale : PB-I Rs.5200 -20,200/- + GP Rs. 2800/
• Qualification : Diploma in Civil/ Marine Mechanical/ Electrical Engineering / Naval Architecture with 1 year experience.

2. Field Assistant : 03 Posts
• Pay Scale : PB-I Rs.5200 -20,200/- + GP Rs. 2000/
• Qualification : 1. Matriculation passed with ITI Certificate in survey and Draftsmanship. 2. 1 Year survey experience including hydrographic survey in a reputed organization. 3. Knowledge of swimming

Age Limit : Not exceeding 25 years on the closing date of application

Last Date for receiving application : 45 days from 13.10.2011

    Interested candidates may visit the website and submit the application in prescribed format alongwith requisite documents to Secretary, IWAI

For More Detail , Please Visit http://www.iwai.nic.in/misc/Advertisment131011.pdf

ISRO RECRUITMENT

Government of India
Indian Space Research Organisation
Liquid Propulsion Systems Centre
Valiamala PO., Thiruvananthapuram-695 547
Advertisement No. LPSC/03/2011 Dated 10.10.2011

Applications are invited for the following posts for LPSC Units located at Valiamala, Near Thiruvananthapuram and Mahendragiri, Near Nagercoil

1. Scientist/ Engineer-SC : 06 Posts
• Pay Scale : Rs. 15600-39100/- + Grade Pay Rs. 5400/-
• Qualification : BE/B.Tech should be in Ist class with an aggregate minimum of 65%. ME/M.Tech should be in First class with an aggregate minimum of 60%.

2. Medical Officer-SC : 01 Post
• Pay Scale : Rs. 15600 - 39100/- + Grade Pay Rs. 5400/-
• Qualification :MBBS + 2 Years experience

Last Date for Apply : 03.11.2011

    Applications completed in all respects should reach the SR. ADMINISTRATIVE OFFICER, RECRUITMENT SECTION, LIQUID PROPULSION SYSTEMS CENTRE, VALIAMALA PO, THIRUVANANTHAPURAM- 695 547

For More Details, Please Visit http://www.lpsc.gov.in/html/recruitmenthome.htm

Steel Authority Of India Limited Recruitment

Steel Authority Of India Limited
Bhilai Steel Plant
Bhilai, Distt-Durg, Chhattisgarh, India - 490 001
Advt. No: BSL/R/2011-04

Bhilai Steel Plant invites applications from eligible candidates for the following posts

1. Operator-Cum-Technician (Trainee) : 105 Posts
• Pay: Rs. 9160-3%-13150 /- (S-3)
• Age : Minimum age 18 yrs. and maximum age 28 yrs as on 01/10/2011
• Qualification : Diploma in Engineering in one of the following disciplines (Mechanical/ Electrical / Metallurgy / Electronics / Civil)

2. Attendant-cum-Technician (Trainee) : 51 Posts
• Pay: Rs. 8630-3%-12080/- (S-1)
• Age : 18-28 yrs as on 01/10/2011
• Qualification : ITI in any of the following trades Fitter, Electrician, Welder, Turner, Mason, Machinist, Motor Vehicle Mechanic.

Closing date : 12.11.2011
For More Detail , Online Apply, Please visit http://sail.shine.com/

Neyveli Lignite Corporation Limited Recruitment

Neyveli Lignite Corporation Limited looking for energetic & result oriented professionals for Leadership Positions in the field of Power Project Construction / Operation & Maintenance / Mining / Corporate Planning/ Finance, etc., for its units and facilities located in various parts of the country (and abroad in future).

1. Chief General Manager: 03posts
2. General Manager: 09posts
3. Deputy General Manager: 19posts
4. Mechanical (engineer): 18posts
5. Electrical (engineer): 17posts
6. Civil (engineer): 03posts
7. Instrumentation ((engineer): 08posts
8. Chemical (engineer):02posts
9. Geology (Asst. Executive Manager): 01post
10. Mining (engineer): 26posts
11. Mine Survey (Asst. Executive Manager): 04posts
12. Scientific (Dy. Manager): 01post
13. Indusial Engineering (engineer):03posts
14. Finance (Addl. Chief Manager): 13posts
15. Human Resource (manager): 08posts
16. Company Secretarial (Asst. Company Secretary): 01post
17. Official Language (Hindi officer): 01post
18. Medical (officers): 17posts
19. Medical (Asst. Medical Officer): 07posts

Application fee: General & OBC Candidates will be required to deposit the Application Fee of Rs.300/- Application fee is non-refundable
How to apply: Apply Online only through NLC'S Website-Www.Nlcindia.Com. To The Chief Manager (Hr), Recruitment Cell, Human Resource Department, Corporate Office, Neyveli Lignite Corporation Limited, Block-1, Neyveli – 607801, Tamilnadu.

Imp Date:
1. Online Registration Starting Date 27-10-2011.
2. Online Registration Closing Date 14-11-2011
3. Last Date for Receipt of Registration-cum-Application Form 24-11-2011

For more details Click here

Experienced Engineering Executives on Fixed Tenure Basis in BHEL

The posts are purely temporary in nature and offered on fixed tenure basis for a period of 24 months only. This post is not against any permanent vacancy. This placement will not entitle the candidate for any regular / permanent employment in BHEL in future.

Name of the Post: Engineering Executives
Number of Vacancies: 20

• Civil- 10
• Mechanical- 5
• Electrical or Electronics- 5

Eligibility:
For the Post of civil Engineering Executives:
Bachelors Degree in Engineering/ Technology in CIVIL from a recognized University / Institute with minimum 60% marks in aggregate of all the years / semesters for Gen/OBC/and 50% marks in aggregate for SC/ST candidates Work Experience
Minimum ONE-YEAR relevant Work Experience.
For the Post of Mechanical Engineering Executives:
Bachelors Degree in Engineering/ Technology in Mechanical from a recognized University / Institute with minimum 60% marks in aggregate of all the years / semesters for Gen/OBC/and 50% marks in aggregate for SC/ST candidates
Work Experience
Minimum ONE-YEAR relevant Work Experience
For the Post of Electrical/Electronics Engineering Executives:
Bachelors Degree in Engineering/ Technology in Electrical/ Electronics from a recognized University / Institute with minimum 60% marks in aggregate of all the years / semesters for Gen/OBC/and 50% marks in aggregate for SC/ST candidates

Work Experience Minimum ONE-YEAR relevant Work Experience.
Age: 33 years as on 01.10.2011.
Age relaxation:
3 years for OBC (Non Creamy Layer).
5 years for SC/ST candidates.
10 years for Physically Challenged candidates with Locomotor disability or Hearing Impairment. The definition of Locomotor disability and Hearing Impairment for Physically Challenged candidates is as per The Persons with Disabilities.

Selection Process:
Selection process will comprise of Personal interview of eligible candidates.

Pay- Scale:
Selected candidates will be paid an all-inclusive monthly consolidated remuneration of Rs. 36,660/- In addition re-imbursement will be made for premium paid for Mediclaim policy upto Rs.2 lakhs for self & family. How to Apply : interested candidates may Submit their Applications to the Online only. The Web sites for submitting the applications are www.bhelisg.com.OR http://careers.bhel.in
A non-refundable Bank Demand Draft for Rs.200/- (Rupees two hundred only) drawn in favour of BHEL, ISG payable at Bangalore is to be enclosed. Candidates are advised to write their name and position on the reverse side of the Demand Draft. However, SC/ST and Physically Challenged candidates are exempted from paying the processing fee.

Duly filled-in and signed application form downloaded from our website www.bhelisg.com or http://careers.bhel.in with requisite documents enclosed including Demand Draft and a photograph pasted are to be sent to
The Addl.General Manager (HR),
BHEL/Industrial Systems Group,
Prof. CNR Rao Circle,
IISc (PO), PB No.1249,
Malleswaram,
Bangalore – 560 012

Important Dates:

• Commencement of Online Submission of Applications -14.10.2011
• Closing of Online Submission of Applications -05.11.2011
• Last date for Submitting the application form -12.11.2011
• Last date for Submitting the application form from far flung areas -19.11.2011

For more details Click here

HLL LIFECARE LIMITED RECRUITMENT

HLL LIFECARE LIMITED
(A Govt. of India Enterprise)

HLL Lifecare Limited (HLL) is a Mini Ratna Central Public Sector Enterprise, under the administrative control of Ministry of Health & Family Welfare invites applications for the following posts

1. Deputy Manager in Civil / Electrical / Mechanical
• Scale of Pay : Rs.16400-40500 , Annual CTC : Rs. 5.1 lakhs (approx.)
• Age : 40 Years as on 01/Oct/2011
• Qualification :BE/B.TECH (CIVIL) (Full-Time Course Only) Civil / Electrical / Mechanical with 60% marks

2. Management Trainees (Engineering)
• Pay : Rs.20,000/- per month during training period
• Age : 30 Years as on 01/Oct/2011
• Qualification :BE/B.TECH (CIVIL) (Full-Time Course Only) Civil / Electrical / Mechanical with 60% marks

Last Date for apply online : 22.10.2011

For More Detail , Please visit Vacancy Detail